Just downloaded the Pro. The software reconizes my Aeon controller and GE light switch but I get a "?" for the Train thermostat and Schlage door sensor. Seems like this is stuck on the free version even though it says Pro at the top. What am I missing?
Edit: Didn't realize the "Not Licensed" was a selection ribbon. I think I got it.
Train TS and Schlage Door sensor not reconized
- 55 Views
- Last Post 23 January 2013
MadSci
posted this
21 January 2013
Ryan-Scott
posted this
21 January 2013
Just downloaded the Pro. The software reconizes my Aeon controller and GE light switch but I get a "?" for the Train thermostat and Schlage door sensor. Seems like this is stuck on the free version even though it says Pro at the top. What am I missing?
Edit: Didn't realize the "Not Licensed" was a selection ribbon. I think I got it.
Are you all set then? If you can't clear it up, restart InControl and it will clear things up.
MadSci
posted this
23 January 2013
So I've got the Aeon S2, Train Z-wave HVAC controller, Schladge door/window sensor, GE switches, and a Foscam. Have the Android running JB.
- GE Switch is fine.
- Train works 80%. The desktop app "auto" mode takes it to off (so does "off"). Heat and cool go to the right mode. None of the energy savings modes work. Train breaks things down into two sub-categories: System Mode: Off/heat/Cool/Auto, and, Schedule Mode: Hold/Run/ESM. The Android app software shows ON/OFF for control, which ends up flipping between the RUN/ESM states respectively. Sometimes it shows "Off" (ESM) when the Train is on RUN ("ON"). If it is not correct, taking it to "ON" keeps the Train in Run mode. Otherwise, it's solid. I'd be happy to beta test code if you need someone to test updated for this device.
-Schladge worked and now it doesn't. doesn't show any status change from tripped/open. I've tried re-associating, wiping the USB stick, and even re-installing InControl, though, I can't seem to delete the entire program because all the settings are coming back. Any ideas?
MadSci
posted this
23 January 2013
So I've got the Aeon S2, Train Z-wave HVAC controller, Schladge door/window sensor, GE switches, and a Foscam. Have the Android running JB.
- GE Switch is fine.
- Train works 80%. The desktop app "auto" mode takes it to off (so does "off"). Heat and cool go to the right mode. None of the energy savings modes work. Train breaks things down into two sub-categories: System Mode: Off/heat/Cool/Auto, and, Schedule Mode: Hold/Run/ESM. The Android app software shows ON/OFF for control, which ends up flipping between the RUN/ESM states respectively. Sometimes it shows "Off" (ESM) when the Train is on RUN ("ON"). If it is not correct, taking it to "ON" keeps the Train in Run mode. Otherwise, it's solid. I'd be happy to beta test code if you need someone to test updated for this device.
-Schladge worked and now it doesn't. doesn't show any status change from tripped/open. I've tried re-associating, wiping the USB stick, and even re-installing InControl, though, I can't seem to delete the entire program because all the settings are coming back. Any ideas?
MadSci
posted this
23 January 2013
So I've got the Aeon S2, Train Z-wave HVAC controller, Schladge door/window sensor, GE switches, and a Foscam. Have the Android running JB.
- GE Switch is fine.
- Train works 80%. The desktop app "auto" mode takes it to off (so does "off"). Heat and cool go to the right mode. None of the energy savings modes work. Train breaks things down into two sub-categories: System Mode: Off/heat/Cool/Auto, and, Schedule Mode: Hold/Run/ESM. The Android app software shows ON/OFF for control, which ends up flipping between the RUN/ESM states respectively. Sometimes it shows "Off" (ESM) when the Train is on RUN ("ON"). If it is not correct, taking it to "ON" keeps the Train in Run mode. Otherwise, it's solid. I'd be happy to beta test code if you need someone to test updated for this device.
-Schladge worked and now it doesn't. doesn't show any status change from tripped/open. I've tried re-associating, wiping the USB stick, and even re-installing InControl, though, I can't seem to delete the entire program because all the settings are coming back. Any ideas?
MadSci
posted this
23 January 2013
Well, the door sensor works now. Didn't do anything. I'll let you know if I start having problems again.
MadSci
posted this
23 January 2013
Also, how can I use the device state/change level trigger an email when the Train temperature sensor temperature falls out of the desired range (Monitor for HVAC failures and the such...)?
